1-1/8" I.D. × 6' Polyethylene Bilge and Pump Discharge Hose
Replace a worn hose or complete the water-delivery system for your Gold Cube, power sluice, highbanker, bilge pump, or other compatible prospecting equipment.
This six-foot polyethylene discharge hose has a 1-1/8-inch inside diameter and molded smooth cuffs every three feet. Its corrugated construction provides the flexibility needed for portable prospecting setups while resisting tears, punctures, abrasion, and kinking during normal discharge use.
Fits the Gold Cube Top-Tray Fitting
The 1-1/8-inch inside diameter is compatible with the hose fitting used on the Gold Cube top tray. It can also be used with properly sized bilge pumps, highbankers, power sluices, sump pumps, and other low-pressure water-discharge systems.
Always verify the outside diameter of your pump outlet or hose-barb fitting before ordering. Secure the hose with an appropriately sized clamp when required.
Key Features
-
1-1/8-inch inside diameter
-
Six-foot overall length
-
Flexible corrugated polyethylene construction
-
Smooth molded cuffs every three feet
-
Fits the Gold Cube top-tray hose fitting
-
Suitable for prospecting pumps and power sluices
-
Tear and puncture resistant
-
Abrasion and kink resistant
-
Stable at elevated operating temperatures
-
Maximum operating temperature of 150°F
-
Suitable for low-pressure water-discharge applications
-
Can be cut at the center cuff to create two shorter sections when needed
Designed for Discharge Applications
This hose is intended to carry water away from a pump. It works well for portable gold-prospecting equipment because it is lightweight, flexible, and easy to route between a pump and header box or other water inlet.
It is not designed for suction, vacuum, or high-pressure applications. Installing it on the intake side of a pump may cause the corrugated hose to collapse and restrict water flow.
Prospecting Applications
Use this hose with compatible:
-
Gold Cube concentrators
-
Power sluices
-
Highbankers
-
Recirculating gold-recovery systems
-
Gold-cleanup equipment
-
12-volt bilge pumps
-
Low-pressure transfer pumps
-
Marine bilge systems
-
Sump-pump discharge systems
Compatibility depends on the equipment’s fitting diameter and operating requirements.
Product Specifications
-
Product type: Corrugated pump-discharge hose
-
Material: Polyethylene
-
Color: Milky white
-
Inside diameter: 1-1/8 inches
-
Overall length: 6 feet
-
Maximum corrugated outside diameter: Approximately 1.377 inches
-
End-cuff outside diameter: Approximately 1.20 inches
-
Molded cuff spacing: Every 3 feet
-
Maximum operating temperature: 150°F
-
Application: Low-pressure discharge
-
Vacuum rated: No
-
High-pressure rated: No
-
Pack quantity: One hose
What’s Included
Not Included
Installation Notes
-
Confirm that the hose’s 1-1/8-inch inside diameter matches your equipment.
-
Slide the smooth cuff completely over the discharge fitting.
-
Secure the connection with a properly sized hose clamp when required.
-
Route the hose without sharp bends or pinch points.
-
Check for leaks before beginning normal operation.
-
Inspect the hose regularly for cuts, punctures, and damaged cuffs.
Do not exceed the pump or hose manufacturer’s operating limits.
Keep your Gold Cube, highbanker, or power sluice supplied with water using this lightweight and flexible six-foot discharge hose.
This 1-1/8 in. I.D. x 6 ft. bilge and pump hose is specifically engineered to withstand high temperatures while ensuring maximum durability. Its superior tear strength and high impact puncture resistance make it a top choice for prospecting, marine, sump pump, and all discharge operations where vacuum is not present. The cuffs are molded every 3 ft. for easy use without the need for additional fittings. With a maximum operating temperature of 150°F, this hose provides exceptional performance. Fits Gold Cube top tray fitting.
